DSE 8610 Argus EMS ile nasıl bağlanır?

DSE 8610/8620 yerleşik Modbus TCP destekler. DSE'nin ethernet portundan LAN kablosuyla Field Agent PC'sine bağlanır. Port: 502, Slave ID: genellikle 1. Argus cihaz şablonu register haritasını otomatik yükler.

Jeneratör yakıt seviyesi takibi yapılabilir mi?

Evet. DSE modülü yakıt seviyesini yüzde olarak raporlar. Argus'ta eşik alarmı tanımlanır (%20 altı kritik); mail bildirimi otomatik gönderilir.

Jeneratör ATS geçişleri loglanır mı?

Evet. DSE'nin event log kayıtları ve Argus'un alarm motoru birlikte çalışır. Şebeke kaybı, jeneratör start, senkronizasyon ve şebekeye dönüş olayları zaman damgasıyla kaydedilir.

Hastanede UPS + jeneratör birlikte izlenebilir mi?

Evet. Argus EMS, aynı proje içinde UPS (SNMP/Modbus) ve jeneratör (DSE) cihazlarını birlikte izler. Kritik güç zinciri tek dashboard'da görünür: şebeke → UPS → jeneratör → yük.

⚡ Modbus TCP Integration Guide

DSE 8610/8620

Deep Sea Electronics DSE 8610/8620 Genset Kontrol Modülü — Real-time power, energy and alarm monitoring via Modbus TCP protocol with Argus EMS.

All Devices →

Monitored Parameters

Register (Hex)	Parameter	Unit	Scale
0x0001	Motor Hızı (RPM)	RPM	×1
0x0002	Batarya Gerilimi	V	×0.01
0x0003	Motor Soğutma Sıcaklığı	°C	×1
0x0004	Yağ Basıncı	kPa	×1
0x0060	Jeneratör Gerilim L1	V	×0.1
0x0062	Jeneratör Gerilim L2	V	×0.1
0x0064	Jeneratör Gerilim L3	V	×0.1
0x0068	Jeneratör Frekansı	Hz	×0.1
0x006E	Aktif Güç Toplam	kW	×1
0x0071	Güç Faktörü	-	×0.01
0x0174	Çalışma Saati	saat	×0.1
0x0175	Yakıt Seviyesi	%	×1

Connection

How to Connect to Argus EMS

Physical Connection

Connect the device to the RS-485 or Ethernet network. Configure Slave ID and baud rate from the device front panel or web interface.

Add Device in Argus

From the Argus web panel click "New Device". Select DSE 8610/8620 from the template list — the register map loads automatically.

Live Monitoring

The Field Agent tests the connection; the first reading appears on the dashboard within 60 seconds. Alarm thresholds are configured.

Monitored Metrics

What Can You Monitor?

Engine speed (RPM), temperature, oil pressure
Battery voltage and charge status
Generator L1/L2/L3 voltage and current
Total active power (kW) and energy (kWh)
Running-hours counter and fuel level
Fault codes and alarm status
Automatic start/stop (ATS) event log
Periodic test-run tracking

Critical Power Monitoring

Why Is Generator Monitoring Critical?

🏥

Hospitals

Generator start delay is critical in operating theatres and ICUs. Argus reports low-battery and low-fuel alarms in advance.

🏢

Data Centres

Generator active power tracking is essential for PUE calculation. The running-hours log automates maintenance planning.

🏭

Factories

During a production line outage, generator load capacity adequacy is visible instantly. The overload alarm prevents critical machine loss.

FAQ

Frequently Asked Questions

How does the DSE 8610 connect to Argus EMS?

The DSE 8610/8620 has built-in Modbus TCP support. Connect the DSE Ethernet port to the Field Agent PC via LAN cable. Port: 502, Slave ID: typically 1. The Argus device template loads the register map automatically.

Can generator fuel level be tracked?

Yes. The DSE module reports fuel level as a percentage. A threshold alarm is configured in Argus (below 20% is critical); email notification is sent automatically.

Are generator ATS transitions logged?

Yes. DSE's event log records and Argus's alarm engine work together. Grid loss, generator start, synchronisation, and return-to-grid events are recorded with timestamps.

Can UPS and generator be monitored together in a hospital?

Yes. Argus EMS monitors UPS (SNMP/Modbus) and generator (DSE) devices together within the same project. The critical power chain is visible on a single dashboard: grid → UPS → generator → load.

Integrate Into Your System

Request a demo; our experts will manage the DSE 8610/8620 integration process.